Available Monday-Friday, 8AM-6PM CT (US & Canada), 9AM-5PM CET (Europe), 9AM-5PM HKG (Asia).

Live Chat Not Available: Create Service Request

K70_120: Kinetis K70 Graphic LCD 120/150 MHz MCUs

The Kinetis K70 MCU family includes 512KB-1MB of flash memory, a single precision floating point unit, Graphic LCD Controller, IEEE 1588 Ethernet, full- and high-speed USB 2.0 On-The-Go with device charge detect, hardware encryption, tamper detection capabilities and a NAND flash controller. 256-pin devices include a DRAM controller for system expansion. The Kinetis K70 family is available in 256 pin MAPBGA packages.

Features

Ultra-Low-Power

10 low-power modes with power and clock gating for optimal peripheral activity and recovery times. Stop currents of <500 nA, run currents of <200 µA/MHz, 4 µs wake-up from Stop mode
Full memory and analog operation down to 1.71 volts for extended battery life
Low-leakage wake-up unit with up to eight internal modules and 16 pins as wake-up sources in low-leakage stop (LLS)/very low-leakage stop (VLLS) modes
Low-power timer for continual system operation in reduced power state

Flash, SRAM and FlexMemory

512 KB-1 MB flash. Fast access, high reliability with four-level security protection
128 KB of SRAM
FlexMemory: 32 bytes-16 KB of user-segmentable byte write/erase EEPROM for data tables/system data. EEPROM with over 10M cycles and flash with 70 µsec write time (brownouts without data loss/corruption). No user or system intervention to complete programming and erase functions and full operation down to 1.71 volts. In addition, 512KB of FlexNVM for extra program code, data or EEPROM backup

Mixed-Signal capability

Up to four high-speed 16-bit analog-to-digital converter (ADC) with configurable resolution. Single or differential output mode operation for improved noise rejection. 500 ns conversion time achievable with programmable delay block triggering
Up to two 12-bit digital-to-analog converter (DAC) for analog waveform generation for audio applications
Up to four high-speed comparators providing fast and accurate motor over-current protection by driving PWMs to a safe state
Up to four programmable gain amplifiers with x64 gain for small amplitude signal conversion
Analog voltage reference provides an accurate reference to analog blocks, ADC and DAC, and replaces external voltage references to reduce system cost

Performance

ARM® Cortex™-M4 core + DSP. 120-150 MHz, single cycle MAC, single instruction multiple data (SIMD) extensions, single precision floating point unit
Up to 32-channel DMA for peripheral and memory servicing with reduced CPU loading and faster system throughput
Cross bar switch enables concurrent multi-master bus accesses, increasing bus bandwidth
Up to 16 KB of instruction/data cache for optimized bus bandwidth and flash execution performance
Independent flash banks allow concurrent code execution and firmware updating with no performance degradation or complex coding routines

Timing and Control

Up to four FlexTimers with a total of 20 channels. Hardware dead-time insertion and quadrature decoding for motor control
Carrier modulator timer for infrared waveform generation in remote control applications
Four-channel 32-bit periodic interrupt timer provides time base for RTOS task scheduler or trigger source for ADC conversion and programmable delay block

Human-Machine Interface

Graphic LCD Controller - supports colour QVGA displays as single chip or up to 24-bit SVGA displays using external memory. Supported by Freescale's Portable Embedded GUI (PEG) Library with simple WindowBuilder interface for powerful GUI development
Hardware touch-sensing interface with up to 16 inputs. Operates in all low power modes (minimum current adder when enabled). Hardware implementation avoids software polling method. High sensitivity level allows use of overlay surfaces up to 5 mm thick

Connectivity and Communications

IEEE 1588 Ethernet MAC with hardware time stamping provides precision clock synchronization for real-time industrial control
USB 2.0 On-The-Go (full and high speed). Device charge detect optimizes charging current/time for portable USB devices enabling longer battery life. Low-voltage regulator supplies up to 120 mA off chip at 3.3 volts to power external components from 5 volts input
Up to six UARTs with IrDA support including one UART with ISO7816 smart card support. Variety of data size, format and transmission/reception settings supported for multiple industrial communication protocols
Inter-IC Sound (I²S) serial interface for audio system interfacing
Up to two CAN modules for industrial network bridging
Up to three DSPI and two I²C

Reliability, Safety and Security

Hardware Encryption coprocessor for secure data transfer and storage. Faster than software implementations and with minimal CPU loading. Supports a wide variety of algorithms - DES, 3DES, AES, MD5, SHA-1, SHA-256
System security and tamper detect with secure real-time clock with independent battery supply. Secure key storage with internal/external tamper detect for unsecure flash, temperature, clock, and supply voltage variations and physical attack detection
Memory protection unit provides memory protection for all masters on the cross bar switch, increasing software reliability
Cyclic redundancy check engine validates memory contents and communication data, increasing system reliability
Independent-clocked COP guards against clock skew or code runaway for fail-safe applications such as the IEC 60730 safety standard for household appliances
External watchdog monitor drives output pin to safe state external components if watchdog event occurs

Featured Documentation

K70P256M120SF3: K70 Sub-Family Data Sheet for 120 MHz devices in 256 pin packages - Data Sheet
K70PB: K70 Family - Product Brief
KNTSK70FS: Kinetis K70 Family: Low-power MCUs with graphics LCD, connectivity and security - Fact Sheet
K70_INFOCTR: K70 Graphic LCD MCU Infocenter—Online Documentation